腐蚀对模块式钢结构选煤厂设备支架振动响应影响的测试及分析

选煤厂采用模块式钢结构作为设备支架,受设备使用及养护不当造成结构构件严重腐蚀,构件截面削弱,导致结构产生过大振动,通过对结构各层振动响应测试,得到各测点水平向及竖直向振动速度幅值。经分析得出腐蚀后对结构整体刚度影响程度,为后期采取措施及安全生产提供依据。     

Propagation and termination of an internal crack in continuously cast austenitic stainless steel analyzed by ∑ values and the Schmid factor

The formation mechanism of an internal crack was clarified from the viewpoint of the crystallography and thermal expansion. An inverse pole figure map obtained by EBSD pattern showed that the crack propagated along the grain boundaries having high ∑ values within the columnar zone. After the crack initiation, these positions were considered to undergo cracking followed by propagation toward the equiaxed side. Near the termination position, the grains ahead of crack propagation had a Schmid factor higher than 0.45 consuming elastic strain energy. Thermal expansion measurements showed that the grain with (0 0 1) orientation had the largest expansion while that with (0 1 1) the smallest. The grain boundaries neighboring the combination of (0 0 1) and (0 1 1) grains had the largest thermal stress. Therefore, thermal stress contributed to the initiation of cracking. It was thus proposed to enlarge the equiaxed zone to prevent cracking by discontinuing the crack propagation.     

Economic Indicators

Currency exchanges rates – updated monthly. Economic indicators of industrial production. Countries included: France, Germany, Italy, the United Kingdom, the United States, Canada, Japan (Total G-7), Eurozone and Total EU-28 (Total OECD). Updated monthly. Economic indicators of car registration in the United States, Canada, France, Germany, Italy, Poland, Spain, Turkey, the United Kingdom, Japan, Republic of Korea and Other OECD (Total OECD-30). Updated monthly. Monthly averages of crude steel production in thousand metric tons for the United States, Canada, Brazil, Mexico, Austria, Belgium, Czech Republic, France, Germany, Italy, Netherlands, Poland, Spain, Sweden, Turkey, the United Kingdom, Russia, Ukraine, South Africa, Iran, China, India, Japan, Republic of Korea, Taiwan and Australia.     

CO2对油田地下水环境中Q235钢和X70钢腐蚀行为的影响

为了探明辽河油田地下水环境中CO₂对Q235钢和X70管线钢的腐蚀规律,采用动电位极化技术及交流阻抗技术研究了不同CO₂浓度对该环境下两种钢腐蚀行为的影响,并利用光学显微镜对试样腐蚀界面进行表征。结果表明:随着CO₂浓度的增加,Q235和X70钢的交流阻抗图谱的半径均减小,腐蚀电流密度增大,腐蚀坑数量、深度和面积都增加,腐蚀敏感性增大。在低浓度CO₂环境下(CO₂含量为10%时),Q235钢的腐蚀敏感性比X70钢更高;而在高浓度CO₂环境下(CO₂含量为20%、40%、60%时),Q235钢的腐蚀速率反而较小,耐腐蚀性更好。     

4140钢弯壳体断裂原因分析和改进措施

某钻具厂生产的一个批次的4140钢螺杆钻具弯壳体出现较多断裂。通过化学成分、力学性能和显微组织分析对失效弯壳体断裂原因进行了研究,并相应优化了热处理工艺。结果表明:弯壳体失效断裂主要原因是由于淬火过程中未淬透,导致显微组织存在大量条状和块状铁素体,未淬透的组织导致材质的强度、硬度和冲击性能较差,从而导致断裂。采用优化的淬火工艺,材料寿命达到了正常水平。     

再加工工艺对N18锆合金板残余应力的影响

采用“热轧+冷轧+退火”工艺对N18锆合金板进行再加工,通过X射线法分析板的表面残余应力,采用EBSD技术分析晶界取向差角分布和大小角度晶界。结果表明,热轧后N18锆合金板的表面残余应力呈现无规律分布状态;冷轧后板的表面残余应力均为压应力,其大小随着冷轧变形量的增加而增加;退火后板的表面残余应力值处于较低水平,当退火制度为500 ℃×2 h时,残余应力处于最低水平;退火后,板的微观结构以小角度晶界为主,且随着退火温度的升高,小角度晶界的密度先增加后趋于稳定。     

35CrMo钢表面铁基激光熔覆层的组织和耐磨性能

采用CO2激光熔覆装置将LC3530铁基粉熔覆在35CrMo钢基体表面,研究了熔覆层的显微组织、硬度和耐磨性能,并与基体的进行对比。结果表明:基体组织为回火索氏体,晶粒尺寸在20μm左右,而熔覆层的组织为均匀细小的等轴晶,晶粒尺寸大多在8μm;基体的平均硬度为254.1HV,而熔覆层的平均硬度为640.5HV,且硬度分布更加均匀;在相同试验条件下,熔覆层试样的磨损量仅为基体试样的1/7,磨损系数是基体试样的1/5,且磨损后熔覆层试样的表面粗糙度较磨损前的大幅下降,表明激光熔覆后35CrMo钢的耐磨性能得到显著提高;基体试样的磨损机制为犁削磨损,而熔覆层试样的磨损机制为微观切削,其优异的耐磨性能与含有铁、铬、钼和碳等元素的高硬度合金碳化物的形成有关。     

35CrMo钢组织遗传消除工艺研究

通过对船用长轴类大锻件的热处理工艺研究得知,采用临界区高温侧正火热处理工艺可以有效消除35CrMo钢组织遗传现象,细化晶粒。     

API X52管线钢与Corus RQT 701超高强钢的焊接工艺

针对超高强钢在机械行业的广泛使用,焊接接头易出现淬硬脆化、裂纹等缺陷的情况,采用焊条电弧焊(SMAW)和药芯气体保护焊(FCAW-GS)组合的焊接方法,对API X52管线钢与Corus RQT 701超高强钢的焊接进行了工艺试验,并进行常规力学性能试验。结果表明,通过合理匹配焊接工艺参数,严格控制低热输入量及层间温度,实现了小熔合比的异种钢焊接,且焊接接头具有良好的力学性能,达到了标准和规格书的要求;异种高强钢焊接,采用SMAW打底焊接和FCAWGS填充并盖面的方法,焊接效率较单纯采用焊条电弧焊工艺提高2倍以上。     

Slag eye formation in single and dual bottom purged industrial steelmaking ladles

ABSTRACT

Argon gas is often injected from the bottom of the ladle during steel refining operations. The injected gas interacts with the liquid (metal and slag) bath and enhances the momentum, heat, and mass transfer rate in the melt. However, during these gas–liquid interactions, an opening of the slag layer called slag eye is formed, which exposes the molten metal surface to the atmosphere, which is generally undesirable. In the current work, a transient, three-dimensional mathematical model is used to study the turbulent gas–liquid interactions in single as well as dual bottom blown industrial steelmaking ladles. A Coupled Level Set Volume of Fluid (CLSVOF) model is used for tracking the steel-argon, steel-slag, and argon-slag interfaces, from which the slag-eye area has been predicted. It is found that the inlet gas purging rate, melt height, slag layer thickness, angular and radial positions of the gas inlets affect the slag opening area. Non-dimensional empirical correlations are proposed to predict the slag opening area in both single as well as dual purged ladles, using non-linear regression analysis.